Windscreen Wiper Linkage Push Rod Arms Repair

Product Information

Initial assessment pointed to a serious engine cooling problem, but that was easily fixed. Then there have been leaking fuel pipes, a leaky injector seal, inoperative handbrake, new camshaft and fuel pump drive belts, new differential mountings and a professional interior clean to add to the bill. But we’re still comfortably within budget, including the parts for these jobs... No you shouldn’t drive with a bad wiper linkage. Driving with faulty wipers isn't just potentially dangerous, it's also illegal and could result in a hefty fine if you’re pulled over. Orientation:When refitting motor and connecting the linkage to the crank arm, the linkage is arranged this way to ensure the wiper arms set off in the correct direction.

Fully functioning wipers are a key safety feature in your car so it’s vital that you get them fixed as soon as you notice a problem. What are the signs of a bad wiper linkage? There are clips that can be bought that will hold the ball in place in the cup, however these are a short term fix only. Can I supply my own parts? Evidence:Although these two inner joints (left) attaching the rods to the motor’s crank arm were okay, the nearby gouge showed the linkage had been rubbing against the bulkhead.A scan tool also allows an active test, which means the wiper motor can be activated from the scan tool. Honda recalled the 2003 4-door Honda Accord for windshield wiper motor failures (service bulletin 08-043). This means, if you have to pay for wiper motor repairs, keep the receipt. If there is a recall, you can apply for reimbursement. The cost of a wiper linkage replacement depends on your car and what parts your car's manufacturer recommends. Cost saving:The electric motor will be saved for fitting to the new wiper linkage. Removing this single nut releases the crank arm, which is part of the linkage.

Cleaning up:The remnants of the old hinge covers are lifted off and the underside of the moulding cleaned smooth, and debris removed from the holes. Crumbling:Over the years, UV light had changed the composition of the rubberised hinge covers so much that bits broke away when they were lifted off.Easy to break:Six plastic clips secure the intake moulding. Two fine screwdrivers are used to lift the inner pin slightly, allowing the whole clip to be removed. Repair and protect:…so the wire was soldered, a shrink-sleeve fitted, and the complete harness was encased in conduit and secured clear of the mechanism, out of harm’s way.

Botched:When buying this car, I’d noticed this overlong stud poking out of the scuttle, but was too busy assessing the rest of the car to investigate then. Field repair:The motor plate has, in the past, broken away from the mechanism and been subsequently secured with three self-tapping screws. This is probably when the main damage happened. It’s a ‘get you home’ repair. Crank nut:To ensure the crank nut is tight on the motor shaft, the crank is held firm with one spanner while tightening the 13mm AF nut with another.

Why wipers don't work: troubleshooting tips

Keep it dry:Base of the windscreen was cleaned to reduce water ingress past the intake moulding seal, and moisture-retaining leaves and debris were cleaned from the scuttle. Best way:Because of its width, it’s a struggle to withdraw the moulding into the engine bay – easier to push it up the screen and withdraw it from the side. Electrics:With the moulding clear, the wiper motor’s electrical plug is disconnected by pressing the release tab, then the harness is moved safely out of the scuttle.

Mitsubishi recalled the 2007-2013 Outlander for wiper motor failures (recall SR-17-003). Another Mitsubishi recall (SR-16-010) covers a wiper motor in the 2011−2015 Outlander Sport / RVR.Rubber pegs:The hinge covers are fixed to the intake moulding by rubber pegs through these holes. The pegs can be sliced off from the underside using a craft knife. Wobbly:The rogue stud (with five nuts) was there to support the wiper motor. In reality, the motor plate was holding the stud in place – all very wobbly. Poor visibility out of your windscreen can greatly reduce your reaction time and cause you to miss important signs and dangerous hazards on the road. A wiper system that doesn't clear the screen properly and affects the drivers' visibility is dangerous and will also result in an instant MOT fail. Does a wiper linkage deteriorate with age?